The award you are redeeming still has unused selections! Are you sure you are finished?
Currently Redeeming
Reward
Redeemed So Far
Count
Welcome to your rewards! Thank you for having a party to sell our products. Below is a list of rewards that you have earned. You may redeem each award by clicking it in the list below, and then shop for the products you want from the items presented in the cart. If you change your mind about your selections for a particular award, you may un-redeem it by clicking the red arrow to the left of the award. This will remove the selections you made for that award and you can then redeem it again.
It's simple! Click one of the buttons above to begin redeeming your awards, or if you are finished, click the 'Checkout Now' button to checkout and complete your order.
The selection has been added to your shopping cart
$ 31.99
Keep your pureAir3000 whole-home air purifier running at its peak performance level by replacing the purification plate when necessary. Refer to the original pureAir3000 owner's manual for detailed instructions. pureAir3000 Owner's Manual Compatibility This ceramic purification plate is compatible with a range of air purification equipment that uses corona discharge as its ozone producing mechanism. This includes the following units: EcoQuest Fresh Air 1.0 EcoQuest Fresh Air 1.5 EcoQuest Fresh Air 2.0 EcoQuest Fresh Air 2.5 activTek AP3000 GreenTech GT3000 BLS MCI32K How to Tell if It's Working When the air purifier is on, the purification plate can be detected by smell when the unit is not set on PCO mode. Turn the lights off in the room and look through the front grille at the purification plate. When it is operating properly, the purification plate will produce a dim purple glow. When/How to Clean Using white vinegar or a solution of equal parts warm water and clear ammonia, soak the purification plate for 8-10 hours but do not exceed 12 hours. Using a soft-bristle brush, scrub the wire mesh to remove debris. Rinse thoroughly. Allow the purification plate to dry completely before reinstalling. Use a soft cloth and rubbing alcohol to clean the contacts on the interior of the purifier that touch the purification plate. Removing: Grasp the purification plate on the ceramic portion and gently pull it out of the grooves on the sides. Installing: Holding the purification plate by the ceramic portion, slowly insert it into the purification plate slot, ensuring that the purification plate is sliding into the grooves on either side. NOTE: About halfway in, the purification plate connectors are parted. Continue sliding the purification plate into the purification plate slot until there is approximately one inch of the purification plate remaining outside of the purification plate slot and significant resistance is met. Be careful not to force the purification plate further into the purification plate slot as this could seriously damage your unit. NOTE: NO exchange or return on parts sold for used machines.
Keep your pureAir3000 whole-home air purifier running at its peak performance level by replacing the purification plate when necessary. Refer to the original pureAir3000 owner's manual for detailed instructions.
pureAir3000 Owner's Manual
This ceramic purification plate is compatible with a range of air purification equipment that uses corona discharge as its ozone producing mechanism. This includes the following units:
When the air purifier is on, the purification plate can be detected by smell when the unit is not set on PCO mode.
Turn the lights off in the room and look through the front grille at the purification plate. When it is operating properly, the purification plate will produce a dim purple glow.
Using white vinegar or a solution of equal parts warm water and clear ammonia, soak the purification plate for 8-10 hours but do not exceed 12 hours. Using a soft-bristle brush, scrub the wire mesh to remove debris. Rinse thoroughly. Allow the purification plate to dry completely before reinstalling. Use a soft cloth and rubbing alcohol to clean the contacts on the interior of the purifier that touch the purification plate.
Removing: Grasp the purification plate on the ceramic portion and gently pull it out of the grooves on the sides.
Installing: Holding the purification plate by the ceramic portion, slowly insert it into the purification plate slot, ensuring that the purification plate is sliding into the grooves on either side.
NOTE: NO exchange or return on parts sold for used machines.
Quantity
Please share your opinions on this product with other shoppers Take the opportunity to share your opinion about this exciting product! Click the 'Write A Review' button below to add your review to our site.
